Move Tatrabot 2D mapping - Johanna, Romana, Nicole, Oswaldo, Dušan, Viktor

The project's aim was to let the Tatrabot successfully reach a given target position in a grid environment using A* search algorithm. This is realized by creating an internal two-dimensional-map representing the robot's current position in the environment and its knowledge about probable locations of obstacles, gained from taking ultrasonic measurements during movement. To account for inaccurate movements Tatrabot uses its LED-sensors to perceive and follow the grid's lines.

Movement and Navigation

(Nicole) UTF-8 characters

Implementation of A* Algorithm

Function initialize_plan_data_structures

Initialize the data that will be used to make a plan to go from a starting position to a final position.

Data structures:

• Array of visited blocks by the robot which initially have value 0 for every block except for the block where the robot currently is (value 1).
• A start point in the queue initialized with 0.
• An end point in the queue initialized with 1.

Function insert_into_queue

Inserts values for rows and columns in a queue according to the plan until the starting value of the queue is the same as the ending value.

Data structures:

• Array of rows in queue and columns in queue.
• Starting and ending values of the queue.

Function create_plan

Creates a valid plan, executes initialize_plan_data_structures and while the ending value in the queue is higher than the starting value it assigns the rows and columns in the queue to the current values of the rows and columns. Then it tries a direction forwards or backwards in columns as well as in rows. The algorithm will try to find a suitable route to the goal without leaving the map, avoiding obstacles, and not visiting already visited spaces on the grid. If the space on the grid is suitable for the robot to move there, the function will assign a visited value on that space and sum that movement into the count of the steps from start, and the visited value will be inserted in the queue. When the candidate row and column reaches the destination row and column the queue starting point will have reached the ending point of the queue, meaning that all the points in the queue correspond to the route from start to goal. Finally, it plans the direction in which the robot will move and the corresponding rows and columns through steps. It adds the steps required to go to the goal and it calculates the plan length.

Data structures:

• Array of suitable directions.
• Array of candidate rows and columns.
• Array of visited rows and columns.
• Steps from start based on the candidate rows and columns.
• Plan length based on steps from start.

Coordinate Systems

The robot is using 3 coordinates systems:

• Local
• Global
• Grid

Every ultrasonic sensor has its own local coordinate system. The point [0,0] is oriented in front of each sensor, the X-coordinate is growing from left to right and the Y-coordinate is rising from down to top in the direction of the sensor.

The global coordinate system is used for real calculation. It’s a normal mathematics coordinate system. Each sensor has defined his own shift from global point [0,0].

The grid coordinate system is the last one, which is used for grid representation of the map. The X-coordinate is the same, but the Y-coordinate is switched. This is because a representation of map is stored in a 2-dimensional array. Every point in the real grid is represented as 4 points in our array.

The final calculation is provided on global coordinate system using shifts and final result of seen and unseen is done with vector transformation to grid coordinate system.

Ultrasonic sensor model

(Matej)

Sensors

Rotation Sensors

Robot is capable of performing 3 distinct moves. After each move the position in map is being updated.

Forward

First we force robot to move past line it stands in front of. Then robot starts moving forward tracking the line. If it changed heading (because of any reasons), it corrects it’s heading. If robot turns left, left motor moves while right stops. If it turns right, left motor stops while right corrects heading. If sensor on far right sees the line, it means we traveled far enough (to next perpendicular line), so we set both motors to reverse to get before line again and cycle can repeat.

Right

At first, left motor makes 90 degree turn (to right). Then both motors reverse and after that robot uses forward method to find line and stop in front of it.

Left

Robot moves forward past the line and starts backing with left motor only. Then it moves in a reverse for some more fixed distance and looks for a line with forward method again.

All of these moves move robot to the same position, slightly to the right of the line just in front of next line perpendicular to direction of robot. Therefore these moves can be chained indefinitely.

Ultrasonic Measurement System

Our robot is equiped with 3 HCSRO4P ultrasonic sensors.

Their general directions are:

• Front
• Left
• Right

Sensors are being run in endless loop measuring distances in all 3 directions working through 18 states. There are 6 states for each sensor direction.

• 1 sets value 1 on pin GPIOB13
• 2 clears GPIO13 pid
• 3 waits for value on GPIO12, starting bit
• 4 waits until sensor stops transmitting on GPIO12, which signals that measuring stopped. If transmission doesnt stop until 870ms, waiting stops and default value is used.
• 5 is used as a state signaling that this sensor is already measured and other sensors can be used.
• 6 means that measuring failed, response wasn’t recieved

States 1-6 work with sensor 1, while states 7-12 are used for sensor 2 and 13-18 for sensor 3.

HCSR04P module

This module is the second generation of HC-SR04 Ultrasonic Sensor. Unlike the first generation HC-SR04 that can only operate between 4.8V 5V DC, this new version has wider input voltage range, allow it to work with controller operates on 3.3V. It measures distance using sonar, an ultrasonic (well above human hearing) pulse (40KHz) is transmitted from the unit and distance-to-target is determined by measuring the time required for the echo return.

Features

• HC-SR04P Upgrade version with build-in crystal, more reliable, lower working current.
• Power Supply: 3.3 5 VDC
• Quiescent Current : <2mA
• Working Current: 2.8mA @ 5V
• Effective Angle: <15 degrees
• Ranging Distance : 2 to 400 cm
• Connector: 4-pins header with 2.54mm pitch.
• Dimension: 45mm x 20mm x 15mm
• Weight 8.5g

STM32 platform

STM32 is a family of 32-bit microcontroller integrated circuits by STMicroelectronics. The STM32 chips are grouped into related series that are based around the same 32-bit ARM processor core, such as the Cortex-M7F, Cortex-M4F, Cortex-M3, Cortex-M0+, or Cortex-M0. Internally, each microcontroller consists of the processor core, static RAM memory, flash memory, debugging interface, and various peripherals.

Visual Studio

(Romana)