|
|
| Line 18: |
Line 18: |
| | Further information is available at the Software, Projects and Downloads section. | | Further information is available at the Software, Projects and Downloads section. |
| | This device may be purchased at the external [http://www.minimexle.de MiniMEXLE Shop]. | | This device may be purchased at the external [http://www.minimexle.de MiniMEXLE Shop]. |
| − |
| |
| − |
| |
| − |
| |
| − |
| |
| − | == Building ==
| |
| − |
| |
| − | Although on the Mexle website You can find the complete step-by-step manual of the board
| |
| − | population, we present here our ideas. Instead of building the whole board on the one step,
| |
| − | we start with the blocks, which can work independently.
| |
| − |
| |
| − | First we start to build power supply (i.e. C1-C4, R2, D1, D2, LED, connector X1, test pins
| |
| − | and power supply stabilizer 7805). If You plan to use this board on battery powered applications, You
| |
| − | can immediately replace 7805 stabilisator with low-drop version e.g. National Semiconductor
| |
| − | LM2940CT-5.0.
| |
| − |
| |
| − | After completing test the power supply immediately. See the Fig. 20 and 21 in the
| |
| − | [http://www.minimexle.de/shop/pub/Bauanleitung%20MiniMEXLE%20V3.0.pdf manual] to
| |
| − | find all the points where the voltage should be measured.
| |
| − |
| |
| − | <span style="color: red">Error: The +5V is on the wrong pin in the Fig. 20 manual v3.0.</span>
| |
| − |
| |
| − |
| |
| − | Next step is to populate board with the all necessary power filter capacitors, reset circuit and
| |
| − | an oscillator circuit together with a processor socket. Also the connectors SV1 (ISP Programmer)
| |
| − | and SV2 (processor pins) are on the place.
| |
| − | Without processor on the place test the function of the Reset circuit.
| |
| − | Then You can insert the processor and using the AVR-USB-PROGI You can check if the programmer
| |
| − | is able to read configuration fuses and device signature.
| |
| − | If Yes, then the board is good and You can finish the board population.
| |
| − |
| |
| − | <span style="color: red">Error: The jumper labeled SJ3 on the board is labeled SJ2 in the
| |
| − | schematic diagram on p. 7 in manual v3.0.</span>
| |
| − |
| |
| − | Last step is to [http://www.minimexle.de/shop/pub/Testprogramm%20MiniMEXLE.zip download the test program]
| |
| − | and check if everything is OK.
| |
| − |
| |
| − | <span style="color: red">ToDo: The source code of the test program is missing</span>
| |
| − |
| |
| − | <span style="color: red">ToDo: The fuse setting picture here</span>
| |
| − |
| |
| − | == Changes ==
| |
| − |
| |
| − |
| |
| − | Following changes were realized on my board to improve it:
| |
| − |
| |
| − | 1. Low-drop version of the stabilisator is used
| |
| − |
| |
| − | See http://www.national.com/mpf/LM/LM2940.html
| |
| − |
| |
| − | 2. Display is equipped with pins, board with holes. This enables to use the display
| |
| − | also with a solderless breadboard. Also the holes in the MiniMexle board makes easier
| |
| − | to connect wires to the breadboard.
| |
| − |
| |
| − | [[Image:MiniMexleLCD.jpg]]
| |
| − | [[Image:MiniMexleDisplay.jpg]]
| |
| − |
| |
| − | 3. For the same reason I used three holes on the place of the SV3 connector.
| |
| − |
| |
| − | 4. I did not use the RC filter on the PWM outputs, i.e. don't solder the capacitors C16 and C17
| |
| − | and use wire instead R20 and R23. It is important if You plan to use PWM outputs for motor
| |
| − | control.
| |
| − |
| |
| − | 5. For easier interfacing with a serial communication link I did change slightly the SV4 connector
| |
| − |
| |
| − | [[Image:MiniMexleSV4.png]][[Image:MiniMexleSV4sch.png]]
| |
| − |
| |
| − | 6. And finally, I used the rubber stamps on the bottom to save my table
| |
| − |
| |
| − |
| |
| − | I did also change the connection of the SV4 connector in order to have the serial link
| |
| − | on the three successive pins, which makes easier external connections.
| |
| − |
| |
| − | [[Image:MiniMexleV30changes.png]]
| |
Minimexle is an universal development board for Atmel AVR microprocessor ATmega88, which comes with an
USB programmer, both in the form of the kit. Both programmer and the board are available from the
www.minimexle.de, all documentation is there.
The MiniMEXLE is the youngest child of the MEXLE family. Although it offers many nice features. The device can be connected to a personal computer using the AVR USB Progi.
Processor: ATmega48/88
User interface: 2-lines LCD-Display, 4 Buttons
Analog interface: 2 A/D and D/A-channels
and many more...
The MiniMEXLE is currently in use at Heilbronn University to support students understanding microcontrollers.
Further information is available at the Software, Projects and Downloads section.
This device may be purchased at the external MiniMEXLE Shop.
